Easy Sawdust Fire Starter Bricks John P Neal

Anyone who has ever tried to start a fire when everything in the woods is soaking wet knows the value of a good fire starter. An experienced woodsman can usually locate a pitch pine stump to get a fire started with, but it sure is a lot easier to reach in your pocket and pull out a ready-made emergency fire starter. I have experimented with several different fire starters over the years and have settled on four that I consider the best.

A super simple way to make a fire starter is to take a regular cotton ball and rub petroleum jelly (Vaseline) into it. The cotton ball acts as a wick, and the petroleum jelly is what actually burns, so keep rubbing and pressing until you get the absolute maximum amount of jelly worked into the cotton. I've nick-named these jelly balls, and they really work. I timed one of these little beauties to see just how long it would burn. It burned with a flame for 6 1/2 minutes, and then the cotton continued to burn without a flame for several additional minutes. Six and a half minutes of flame could give you a good edge when it comes to igniting some damp tinder, like shredded cedar bark or very small sticks. I keep six of these jelly balls in a plastic 35mm film can, and drop the can in my pocket every time I head out into the woods.

Another of my favorite fire starters is the paraffin/sawdust fire starter. The paraffin/sawdust starter is more difficult to make than the jelly ball starter, but it burns hotter and longer. In fact, the paraffin/sawdust starter could almost be called a fuel tablet. One of these starters will actually burn long enough and hot enough to boil two cups of water, or you could use it to heat up a dehydrated meal. To make a paraffin/sawdust starter you will need the following materials:
· 1 cardboard toilet paper tube
· 1 sheet of cardboard (tag board, index card, or something of similar
thickness)
· Several inches of masking tape
· 1 cup of sawdust (hardwood is best, pine will do, never use sawdust from
treated lumber)
· 2 cups melted paraffin or candle wax
· Scissors
· A pencil
· A coffee can or old bowl
· A spoon
· A double-boiler

Directions:
1. Cut the toilet paper tube into 4 smaller tubes each about 1″ long
2. Set one of the tubes down on the sheet of cardboard and trace a circle
around the outside of the toilet paper tube. Repeat this three more times
until you have traced out four circles on the sheet of cardboard. Use the
scissors to cut out these four circles.
3. Use 4 short pieces of masking tape to tape one cardboard circle to the
bottom of each tube
4. Place the sawdust into a bowl. Put water in the bottom pan of your double-
boiler and place the paraffin in the top pan of your double boiler. Melt
the paraffin.
5. Slowly pour part of the melted paraffin into the bowl of sawdust. Stir the
sawdust as you add the paraffin. The idea is to saturate the sawdust with
paraffin until it is the consistency of very thick oatmeal.
6. Spoon the sawdust/paraffin mixture into the cardboard tubes until it is even
with the top of each tube. You may want to use the bottom of the spoon to
press the mixture down into the tubes. This helps eliminate air bubbles in
the mixture.
7. Set the filled tubes aside and let them harden for a few minutes.
8. When the mixture in the tubes is fairly firm, dip each tube into the
remaining melted paraffin to coat the outside and bottom of the tube. Dip
them fairly quickly. If they sit in the melted paraffin for too long it can
re-melt the sawdust mixture, and you end up with a big mess. I dip each
tube several times to build up a good layer of wax on the outside.
9. Set the finished tubes aside to dry over-night

Your fire starters are now ready to use. To light one all you need to do is peal back part of the outer cardboard tube and set match or lighter to it. I carry three of these in my backpack when camping, and I keep a couple in the glove box of my truck.

You can make a quick and easy fire starter out of corrugated cardboard, cotton string, and paraffin. Cut strips of corrugated cardboard about 1 1/2″ wide by 9″ long. Roll the cardboard up into a fairly tight cylinder and tie cotton string around it to hold it in place. Hold the end of the string and dip the cardboard cylinder into melted paraffin. Hang the cylinder up to dry for a minute, then dip again. Repeat this process until the cardboard is well coated with wax. I usually leave about an inch of paraffin covered string attached to the fire starter as a wick.

The last fire starter that I want to tell you about is a variation of the corrugated cardboard/paraffin fire starter. This is my own little invention that I call the self-lighting fire starter. To make this fire starter, begin by cutting several squares of corrugated cardboard that are 2 1/4″ by 2 1/4″. Roll each square into a fairly tight cylinder and tie with string, as above. Take one cylinder and dip it into melted paraffin. Hold it in the paraffin for several second so that it is thoroughly soaked. Now lift it out of the paraffin; and, while the paraffin is still soft, push a strike-anywhere kitchen match down into the center of the cylinder. Leave just the head of the match exposed above the top of the cylinder. Now dip the cylinder along with the match head end back into the melted paraffin. Remove quickly. You don't want a heavy coat of paraffin over the match head; just enough to waterproof it. Dip several more times to coat the cylinder thoroughly, but try not to get too much more wax on the match head. Make several of these and store them in an old metal band-aid box. To use these fire starters, just take one out of the box and strike it like a giant match. One SAFETY WARNING: Don't store these fire starters loose in a pack, your clothing, a glove box, or etc. You don't want one of these to rub against something and accidentally ignite.

Well, there you have it. Four simple to make and highly effective fire starters. There's no excuse not to get that fire started now, so go out and enjoy your time in the woods.

barberprongling1995.blogspot.com

Source: https://sensiblesurvival.org/2008/12/27/four-easy-to-make-emergency-fire-starters/

Share this post